Real‐time thermal states monitoring of absorber tube for parabolic trough solar collector with non‐uniform solar flux

With the world energy shortage problem becoming increasingly prominent, more and more attentions have been paid to the development of renewable energies. Among these sources, solar energy has received extensive attention with its excellent characteristics. The thermal state affects the safety of the solar heat collection system. In this paper, real‐time monitoring of the input heat flux on the inside wall and the temperature field simultaneously of an absorber tube for parabolic trough solar collector were studied. Based on the measured temperatures on the outside wall, the fuzzy adaptive Kalman filter coupled with weighted recursive least squares algorithm (WRLSA) was employed to monitor the heat states of the absorber tube inversely, in which WRLSA was used to acquire the heat flux while fuzzy adaptive Kalman filter was adopted to monitor the temperature field. The method showed strong robustness to resist the ill‐posedness. Accurate monitoring results also can be acquired when there are random disturbances of the heat transfer condition on the inner wall.     

槽式太阳能集热管内相变微胶囊悬浮液的热力性能分析

针对传统使用水基和油基的太阳能集热器换热效果低和管壁热应力大的问题，以相变微胶囊悬浮液为工作流体，对抛物型槽式太阳能集热器进行了三维建模。采用蒙特卡罗射线追踪法结合有限容积法和有限元法的方法求解了太阳能集热管的光?热?力耦合问题，采用欧拉?欧拉多相流模型研究了相变微胶囊悬浮液在集热管内的流动换热特性。结果表明，相变微胶囊悬浮液强化了集热管内的对流换热，不仅降低了集热管的沿程壁温，且减少了集热管的周向温差，均化了集热管温度分布。集热管周向等效热应力呈花瓣型分布，对应的5个高温度梯度的位置附近(圆周角θ=5°, 90°, 175°, 225°和315°)出现等效应力局部峰值。吸热管内壁面θ=90°处轴向热应力为压应力，作用于整个管程，而径向热应力和切向热应力为拉应力，主要作用在进出口端。相变微胶囊悬浮液浓度越高，强化换热效果越好，集热管热应力越小，但产生的压降也随之增大。     

A small-scale silica gel-water adsorption system for domestic air conditioning and water heating by the recovery of solar energy

A small-scale silica gel-water adsorption system with modular adsorber, which utilizes solar energy to achieve the cogeneration of domestic air conditioning and water heating effect, is proposed and investigated in this paper. A heat recovery process between two adsorbers and a mass recovery process between two evaporators are adopted to improve the overall cooling and heating performance. First, the adsorption system is tested under different modes (different mass recovery, heat recovery, and cogeneration time) to determine the optimal operating conditions. Then, the cogeneration performance of domestic cooling and water heating effect is studied at different heat transfer fluid temperatures. The results show that the optimal time for cogeneration, mass recovery, and heat recovery are 600 s, 40 s, and 40 s, respectively. When the inlet temperature of hot water is around 85°C, the largest cooling power and heating power are 8.25 kW and 21.94 kW, respectively. Under the condition of cooling water temperature of 35°C, the obtained maximum COP_c, COP_h, and SCP of the system are 0.59, 1.39, and 184.5 W/kg, respectively.     

What is the future of solar energy? Economic and policy barriers

The most important characteristics and limitations of solar energy were reviewed in this study. The analysis of different aspects indicated that the most important global challenges of solar energy development were climatic challenges, technical constraints, and unwillingness to make investments. After describing current conditions and predicting the future of solar energy, this study analyzed the policies formulated by developed countries to develop this from of energy. Accordingly, China has gotten ahead of other countries in this industry due to the technological production of solar panels and governmental supports. Finally, the economic estimation of solar energy was presented by dealing with the economic barriers to this form of energy in developed countries. According to the significant growth in the reduction of solar energy electricity production cost, this source of energy can be used as a major source in the future. It was then recommended to use a hybrid of solar energy with other sources such as wind to reduce the costs.     

Pure CuBi2O4 Photoelectrodes with Increased Stability by Rapid Thermal Processing of Bi2O3/CuO Grown by Pulsed Laser Deposition

A new method for enhancing the charge separation and photo‐electrochemical stability of CuBi₂O₄ photoelectrodes by sequentially depositing Bi₂O₃ and CuO layers on fluorine‐doped tin oxide substrates with pulsed laser deposition (PLD), followed by rapid thermal processing (RTP), resulting in phase‐pure, highly crystalline films after 10 min at 650 °C, is reported. Conventional furnace annealing of similar films for 72 h at 500 °C do not result in phase‐pure CuBi₂O₄. The combined PLD and RTP approach allow excellent control of the Bi:Cu stoichiometry and results in photoelectrodes with superior electronic properties compared to photoelectrodes fabricated through spray pyrolysis. The low photocurrents of the CuBi₂O₄ photocathodes fabricated through PLD/RTP in this study are primarily attributed to their low specific surface area, lack of CuO impurities, and limited, slow charge transport in the undoped films. Bare (without protection layers) CuBi₂O₄ photoelectrodes made with PLD/RTP shows a photocurrent decrease of only 26% after 5 h, which represents the highest stability reported to date for this material. The PLD/RTP fabrication approach offers new possibilities of fabricating complex metal oxides photoelectrodes with a high degree of crystallinity and good electronic properties at higher temperatures than the thermal stability of glass‐based transparent conductive substrates would allow.     

Materials Design of Solar Cell Absorbers Beyond Perovskites and Conventional Semiconductors via Combining Tetrahedral and Octahedral Coordination

Tetrahedral coordination structures, e.g. crystalline Si, GaAs, CdTe, and octahedral coordination structures, e.g. perovskites, represent two classes of successful crystal structures hitherto for solar cell absorbers. Here, via first‐principles calculations and crystal symmetry analysis, the two classes of semiconductors are shown exhibiting complementary properties in terms of bond covalency/ionicity, optical property, defect tolerance, and stability, which are correlated with their respective coordination number. Therefore, a spinel structure is proposed, which combines tetrahedral and octahedral coordination into a single crystal structure, as an alternative to perovskite and conventional semiconductors for potential photovoltaic applications. The case studies of a class of 105 spinel AB₂X₄ systems identify five spinel compounds HgAl₂Se₄, HgIn₂S₄, CdIn₂Se₄, HgSc₂S₄, and HgY₂S₄ as promising solar cell absorbers. In particular, HgAl₂Se₄ has suitable bandgap (1.36 eV by GW0 calculation), small direct–indirect bandgap difference (24 meV), appropriate carrier effective mass (m_e = 0.08 m₀, and m_h = 0.69 m₀), strong optical absorption, and high dynamic stability. This study suggests that crystal systems with mixed tetrahedral and octahedral coordination may open a viable route for emerging solar cell absorbers.     

Diluted chemical bath deposition of CdZnS as prospective buffer layer in CIGS solar cell

In this study, dilute chemical bath deposition technique has been used to deposit CdZnS thin films on soda-lime glass substrates. The structural, morphological, optoelectronic properties of as-grown films have been investigated as a function of different Zn²⁺ precursor concentrations. The X-ray diffractogram of CdS thin-film reveals a peak corresponding to (002) plane with wurtzite structure, and the peak shift has been observed with the increase of the Zn²⁺ concentration upon formation of CdZnS thin film. From morphological studies, it has been revealed that the diluted chemical bath deposition technique provides homogeneous distribution of film on the substrate even at a lower concentration of Zn²⁺. Optical characterization has shown that the transparency of the film is influenced by Zn²⁺ concentration and when the Zn²⁺ concentration is varied from 0 M to 0.0256 M, bandgap values of resulting films range from 2.42 eV to 3.90 eV while. Furthermore, electrical properties have shown that with increasing zinc concentration the resistivity of the film increases. Finally, numerical simulation validates and suggests that CdZnS buffer layer with composition of 0.0032 M Zn²⁺ concentration would be a promising candidate in CIGS solar cell.     

Benzodithiophene-based small molecules with various termini as hole transporting materials in efficient planar perovskite solar cells

In this study we prepared four benzodithiophene (BDT)-based small organic molecules presenting bithiophene (TT), thiophene (FT), carbazole (CB), and triphenylamine (TPA) units, respectively, as termini, and used them as hole transporting materials for perovskite solar cells (PSCs). The high degrees of planarity of these BDT-based small molecules imparted them with high degrees of stacking and charge transport. These small molecules had suitable optical properties and energy level alignments for use in PSCs based on MAPbI₃, with compact-TiO₂ as the electron transporting layer and a BDT-based material as the hole transporting layer, in a n–i–p structure. Among our tested BDT-based materials, the PSC incorporating BDT-TT had the best performance, with an average power conversion efficiency of 13.63%.     

The digital twin of the quality monitoring and control in the series solar cell production line

With the development of intelligent manufacturing (IM), the Digital twin (DT) has become an important means to the evolution mechanism of the process. Many researchers pay attention on the realization of DT in different industries. Based on the DT and Digital Twin Shop Floor (DTS) model, a novel, high throughput metrology method is proposed in the process quality monitoring and control of the Series Solar Cell Production Line (SSCPL) for detailed performance analysis. The variance of individual loss parameters and their impact on quality performance are quantified and mapped into the virtual space. The nature of their distributions and correlations provide great insights about quality loss mechanisms in process monitoring, helping to prioritize efforts for optimizing the control of the SSCPL in the physical space. Additionally, the parameters can be tied back to the physical space, allowing the data to be used directly for the control in the manufacturing. The data-loop of “Autonomous perception of process parameters - Dynamic behaver mapping - Online monitoring - Online data analysis - Parameters configuration & control” can be obtained in the model. This paper provides an application paradigm for DT and IM.     

Surface Reconstruction Engineering with Synergistic Effect of Mixed-Salt Passivation Treatment toward Efficient and Stable Perovskite Solar Cells

Surface passivation treatment is a widely used strategy to resolve trap-mediated nonradiative recombination toward high-efficiency metal-halide perovskite photovoltaics. However, a lack of passivation with mixture treatment has been investigated, as well as an in-depth understanding of its passivation mechanism. Here, a systematic study on a mixed-salt passivation strategy of formamidinium bromide (FABr) coupled with different F-substituted alkyl lengths of ammonium iodide is demonstrated. It is obtained better device performance with decreasing chain length of the F-substituted alkyl ammonium iodide in the presence of FABr. Moreover, they unraveled a synergistic passivation mechanism of the mixed-salt treatment through surface reconstruction engineering, where FABr dominates the reformation of the perovskite surface via reacting with the excess PbI₂. Meanwhile, ammonium iodide passivates the perovskite grain boundaries both on the surface and top perovskite bulk through penetration. This synergistic passivation engineer results in a high-quality perovskite surface with fewer defects and suppressed ion migration, leading to a champion efficiency of 23.5% with mixed-salt treatment. In addition, the introduction of the moisture resisted F-substituted groups presents a more hydrophobic perovskite surface, thus enabling the decorated devices with excellent long-term stability under a high humid atmosphere as well as operational conditions.